ÀÖÌìÌÃappÏÂÔØ

Cutting and Welding Clause Examples

The Cutting and Welding clause establishes the rules and safety requirements for performing cutting, welding, or similar hot work activities on a project site. It typically outlines the necessary precautions, such as obtaining permits, using fire-resistant barriers, and ensuring proper supervision and fire watch during and after the work. This clause is essential for minimizing fire hazards and ensuring compliance with safety regulations, thereby protecting personnel, property, and the overall project from potential accidents related to hot work operations.
Cutting and Welding.ÌýCONTRACTOR shall not permit cutting or welding in or immediately adjacent to existing property of DCAMM or property owned by anyone else without DCAMM’s prior approval in each instance.
View SourceView Similar (6)
Cutting and Welding.ÌýCONTRACTOR shall not permit cutting or welding in or immediately adjacent to existing property of CUSTOMER or property owned by anyone else without CUSTOMER’s prior approval in each instance.
View SourceView Similar (2)
Cutting and Welding.ÌýEmployees covered by this Agreement shall do all cutting and welding whether acetylene or electric when used in connection with any work within the jurisdiction of this Agreement. Any employee covered by this Agreement in cutting or welding shall be furnished an Employee, from within the bargaining unit, currently on the job site to watch after his safety and to protect him from fire, if it is determined necessary by the Job Superintendent.
View SourceView Similar (2)
Cutting and Welding.ÌýThe cutting, threading, bending, welding, drilling and tapping of all conduit, iron, copper or other metals in connection with the installation of electrical materials and equipment shall be performed on the job or at the shop of the Employer by employees covered by this Agreement. Such employees shall perform all channeling, chasing and cutting of metal, stone, masonry, and concrete necessary for the installation of electrical work on the job.
View Source
Cutting and Welding.ÌýEmployees covered by this Agreement shall do all cutting and welding whether acetylene or electric when used in connection with any work within the jurisdiction of this Agreement. Any employee covered by this Agreement in cutting or welding shall be furnished an Employee, from within the bargaining unit, currently on the job site to watch after his safety and to protect him from fire, if it is determined necessary by the Job Superintendent. The Employer shall furnish when engaged in any burning or welding, if required, such protective clothing as gloves, sleeves, aprons, and hoods. All Employees who are engaged in certified welding shall receive not less than One dollar ($1.00) per hour above the minimum hourly rate of pay.
View Source

Related to Cutting and Welding

  • CUTTING AND PATCHING The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.212 â€� MARKET-RELATED CONTRACT TERM ADDITION (11/08). The term of this contract may be adjusted when a drastic reduction in wood product prices has occurred in accordance with 36 CFR 223.52. The Producer Price Index used to determine when a drastic reduction in price has occurred is stated in A20. Purchaser will be notified whenever the Chief determines that a drastic reduction in wood product prices has occurred. If the drastic reduction criteria specified in 36 CFR 223.52 are met for 2 consecutive calendar quarters, after contract award date, Contracting Officer will add 1 year to the contract term, upon Purchaser’s written request. For each additional consecutive quarter such a drastic reduction occurs, Contracting Officer will, upon written request, add an additional 3 months to the term during Normal Operating Season, except that no single 3-month addition shall extend the term of the contract by more than one year. Contracting Officer must receive Purchaser’s written request for a market-related contract term addition before the expiration of this contract. No more than 3 years shall be added to a contract's term by market-related contract term addition unless the following conditions are met:

  • Blasting Blasting shall be permitted only for road construction purposes unless advance permission is obtained from Forest Service. Whenever the Industrial Fire Precaution Level is II or greater, a fire security person equipped with a long handled round point No. 0 or larger shovel and a 5 gallon backpack pump can filled with water, will stay at location of blast for 1 hour after blasting is done. Blasting may be suspended by Forest Service, in areas of high rate of spread and resistance to control. Fuses shall not be used for blasting. Explosive cords shall not be used without permission of Forest Service, which may specify conditions under which such explosives may be used and precautions to be taken.

  • CUTTING AND PATCHING OF WORK 4.14.1 The Contractor shall be responsible for all cutting, fitting or patching that may be required to complete the Work or to make its several parts fit together properly. 4.14.2 The Contractor shall not damage or endanger any portion of the Work or the work of the State or any separate contractors by cutting, patching or otherwise altering any work, or by excavation. The Contractor shall not cut or otherwise alter the work of the State or any separate contractor except with the written consent of the State and of such separate contractor. The Contractor shall not unreasonably withhold from the State or any separate contractor his consent to cutting or otherwise altering the Work.